Firstly read: Safety and Compliance Information
To select H.323 or SIP operation at initial power on, or later, read: SIP / H.323 Dual boot operation.
This page consists of 5 sections, Step-by-step configuration, Utilities, Interoperation, Signalling documents and Additional documents
Then using the table below choose your product, the VoIP protocol and the code version to get the required step-by-step configuration guide.
| SIP with Proxy and Standalone | H.323 with Gatekeeper | H.323 Standalone | |
|---|---|---|---|
| Vega 100 E1 | R5.1, R6 | R5.1 | R5.1 |
| Vega 100 T1 | R5.1, R6 | R5.1 | R5.1 |
| Vega 50 BRI | R4, R6 | R4 | |
| Vega 50 FXS 8 port | R5.1, R7 | R5.1 | R5.1 |
| Vega 50 8FXS and 2FXO port | R5.2, R7 | R5.2 | |
| Vega 50 FXO 8 port | R5.1 | R5.1 | R5.1 |
| Vega 50 FXO 10 port | R5.2 | R5.2 | |
| Vega 50 6x4 FXS ports | R7.5, R8 1 | ||
| Vega 50 6x4 FXO ports | R7.5 | ||
| Vega 50 6x4 BRI ports | R7.5 | R8.0 |
1 *** Upgrade Procedure for Release 7 to Release 8 *** use this document to guide you through upgrading R7.x to R8.x or downgrading R8.x to R7.x
| Utility | |
|---|---|
| SIP REGISTRATION message and SIP INVITE configuration | Use this utility if, once configured, the Vega
does not
provide the information you wanted in the SIP messages. *** R8.0 and above *** *** R7.x and below *** |
| Document | |
|---|---|
| CISCO AS5300 / Vega Guide | How to configure Release 4,5 and 6 Vega gateways and Cisco AS5300s to interoperate |
| Telecount Radius Server | A guide to using the Telecount Radius server to collect Radius billing info |
| BroadSoft with Vega 400 | Guide to configuration of, and interoperation of Vega with BroadWorks R11.1 |
| BroadSoft with Vega 100 | Guide to configuration of, and interoperation of Vega with BroadWorks R11.1 |
| BroadSoft with Vega 50 analogue | Guide to configuration of, and interoperation of Vega with BroadWorks R11.1 |
| Document | |
|---|---|
| BRI connection check-list | Steps to ensure that a BRI Vega is configured to connect to the network correctly |
| E1 / T1 connection check-list | Steps to ensure that an E1 / T1 Vega gateway is configured to connect to the network correctly |
| R2MFC configuration | How to configure E1 Vega gateways to support R2MFC and how to take traces of R2MFC call tones and line signalling |
| Document | |
|---|---|
| Introduction to Vega Dial Plans | How to write dial plans to route, authenticate and apply number translation to incoming calls before onward routing |
| Rack Mount Instructions | How to use the rack mount brackets provided to install the Vega in a 19" rack |
| Vega 100 between PBX and ISDN | Configuration parameters to allow a Vega 100 to transparently pass calls between its two ISDN trunks |
| Vega 400 LAN configuration | How to configure the two LAN interfaces on the Vega 400 for single and dual LAN interface operation |